Salami Group 1 E Series, Group 1.6 E series gear pumps and motors made with alluminium alloy body, flanges and rear covers:

• Displacements from 0,9 cm3/giro (0,05 cu.in./rev.) to 6,5 cm3/giro (0,39 cu.in./rev.)

Salami Group 2 E Series gear pumps made with alluminium alloy body and cast iron flanges and rear covers:

• Displacements from 3,2 cm3/rev (0,19 cu.in./rev.) to 26 cm3/rev (1,58 cu.in./rev.)
• Extremely compact design on the multiple assembling pump for the 2PE type.

Salami Group 2.5 B Series gear pumps made with alluminium alloy body and cast iron flanges and rear covers:

• Displacements from 3,2 cm3/rev (0,19 cu.in./rev.) to 26 cm3/rev (1,58 cu.in./rev.)
• Extremely compact design on the multiple assembling pump for the 2PE type.
• Assembling on multiple stage pump also available in combination with 2PE or 1.5PB types.

Salami Group 3 B series gear pumps and motors made with alluminium alloy body, flanges and rear covers:

• Displacements from 21 cm3/rev (1.26 cu.in./rev.) to 75 cm3/rev (4.48 cu.in./rev.)
• Assembling on multiple stage pump 3PB/3PB available.
• Assembling on multiple stage pump also available in combination with 2PE type.

Salami Group 3.5 B Series gear pumps and motors made with alluminium alloy body, flanges and rear covers:

• Displacements from 55 cm3/giro (3,34 cu.in./rev.) to 98 cm3/giro (6,03 cu.in./rev.)
• Assembling on multiple stage pump 3,5PB/3,5PB available.
• Assembling on multiple stage pump also available in combination with 2PE, 2PB or 3PB types.

Salami Group 2 - E Series gear motors made with alluminium alloy body and cast iron flanges and rear covers:

• Displacements from 4.5 cm3/rev (0,27 cu.in./rev.) to 26 cm3/rev (1,58 cu.in./rev.).
• Rated pressure up to 250 bar (3630 psi) -
• Back pressure capability up to 120 bar (1740 psi) only in by-directional release.

Salami Group 2 E series Gear flow dividers made with alluminium alloy body and cast iron end covers:

• Displacements from 3,2 cm3/rev (0,19 cu.in./rev.) to 30 cm3/rev (1,83 cu.in./rev.)
• Extremely compact design.
• Available also with main relief valves to realign the cylinders at the end of stroke.

Salami Group 3 H Series gear pumps and motors made in spheroidal cast iron:

• Displacements from 21 cm3/rev (1.3 cu.in./rev) to 90 cm3 /rev (5.4 cu.in./rev).
• Assembling on double stage pump 3HP/3HP available.
• Assembling on multiple stage pump also available in combination with 2PB or 2.5PB types.

 Salami PG301 gear pumps made in spheroidal cast iron:

• Displacements from 23 cm3/rev (1.43 cu.in./rev) to 40 cm3 /rev (2.46 cu.in./rev).
• Very compact design, flange, central body, rear cover
• Available as single or double stage pump.

Salami PG330 gear pumps made in spheroidal cast iron:

• Displacements from 23 cm3/rev (1.43 cu.in./rev) to 40 cm3 /rev (2.46 cu.in./rev).
• Very compact design, flange, central body, rear cover
• Available as single or double stage pump.

 Salami VDM6 Directional Control Valve:

• Cast-iron monoblock construction from 1 to 7 working sections.
• Parallel circuit, load check valve protection on down-stream of the pressure "P" line.
• Tandem circuit, only the first working section, l.c.v. protection + l.c.v. protection on down-stream of the "P" line.
• Possibility of power beyond.
• Peveral types of spool: double, single acting, spool motor, float position, regenerative position etc.
• Several spool control devices and spool positioning devices.
   

Salami VDM6A Directional Control Valve: 

• Cast-iron monoblock construction from 1 to 7 working sections.
• Parallel circuit, load check valve protection on each section.
• Possibility of power beyond configuration.
• Several types of spool: double, single acting, spool motor, float position, regenerative position etc.
• Possibility of auxiliary valve either on port A or B or on both.
• Several spool control devices and spool positioning devices. 
   

Salami VDM09 Directional Control Valve:

• Cast-iron monoblock construction from 1 to 6 working sections.
• Parallel circuit, load check valve protection on down-stream of the pressure "P" line.
• Possibility of power beyond.
• Several types of spool: double, single acting, spool motor, float position, regenerative position etc.
• Several spool control devices and spool positioning devices.
   

Salami VDM8 Directional Control Valve:

• Cast-iron monoblock construction from 1 to 5 working sections.
• Parallel circuit, load check valve protection on each section.
• Possibility of power beyond configuration.
• Several types of spool: double, single acting, spool motor, float position, regenerative position etc.
• Possibility of auxiliary valve either on port A or B or on both.
• Several spool control devices and spool positioning devices.
   

 Salami VD6A Directional Control Valve:

• Cast-iron made (inlet section, working section, outlet section) up to 8 working sections.
• Parallel circuit, load check valve protection on each section.
• Series circuit, load check valve protection on each section (possibility of 2nd load check valve on series line)
• Tandem circuit, load check valve protection on each section.
• Possibility of power beyond configuration and possibility of closed center.
• Several types of spool: double, single acting, spool motor, float position, regenerative position etc.
• Several spool control and spool positioning devices.
   

Salami VD8A Directional Control Valve:

• Cast-iron made (inlet section, working section, outlet section) up to 8 working sections.
• Parallel circuit, load check valve protection on each section.
• Series circuit, load check valve protection on each section (possibility of 2nd load check valve on series line)
• Tandem circuit, load check valve protection on each section.
• Possibility of power beyond configuration and possibility of closed center.
• Several types of spool: double, single acting, spool motor, float position, regenerative position etc.
• Several spool control and spool positioning devices. 
   

Salami VDP08 Pressure Sensing Directional Control Valve:

•  Load sensing directional control valve.
• made on cast-iron(inlet section, working section, end section).
• Available with inlet module for fixed or variable displacement pump.
• inlet module with pressure compensator built-in, working modules with pressure compensator built-in..
• Several types of spool: double, single acting, spool motor, float position etc.
• Possibility of auxiliary valve either on port A or B or on both.
• Possibility of pressure relief valve on the LS line coming from the ports.